Code:
# This is an example resource file for rTorrent. Copy to
# ~/.rtorrent.rc and enable/modify the options as needed. Remember to
# uncomment the options you wish to enable.
# Minumum amount of peers to connect per torrent, if available.
min_peers = 40
# Minumum amount of peers to connect per torrent.
max_peers = 60
# Same as above but for seeding completed torrents (-1 = same as downloading)
min_peers_seed = 10
max_peers_seed = 20
# Maximum number of simultanious uploads per torrent.
max_uploads = 4
# Global download rate in KiB. "0" for unlimited.
download_rate = 0
max_memory_usage = 128M
send_buffer_size = 768K
receive_buffer_size = 10K
# Global upload rate in KiB. "0" for unlimited.
upload_rate = 60
# Default directory to save downloaded files. Note it doesn't support
# space yet.
directory = /tmp/btdownload/
# Watch a directory for new torrents, and stop those that have been deleted.
schedule = watch_directory,10,10,load_start=/tmp/hdd/volumes/HDD1/torrent/*.torrent
schedule = untied_directory,10,10,stop_untied=
schedule = tied_directory,10,10,start_tied=
# Close torrents when diskspace is low.
#schedule = low_diskspace,5,60,close_low_diskspace=100M
# Default session directory. Make sure you don't run multiple instance
# of rtorrent using the same session directory. Perhaps using a
# relative path?
session = /opt/share/torrent/session
# The ip address reported to the tracker.
#ip = rakshasa
# The ip address the listening socket and outgoing connections is
# bound to.
#bind = rakshasa
# Port range to use for listening.
port_range = 51777-51777
# Start opening ports at a random position within the port range.
#port_random = no
# Check hash for finished torrents. Might be usefull until the bug is
# fixed that causes lack of diskspace not to be properly reported.
#check_hash = no
# Set whetever the client should try to connect to UDP trackers.
#use_udp_trackers = yes
# Alternative calls to bind and ip that should handle dynamic ip's.
#schedule = ip_tick,0,1800,ip=rakshasa
#schedule = bind_tick,0,1800,bind=rakshasa
#
# Do not modify the following parameters unless you know what you're doing.
#
check_hash = no
# Hash read-ahead controls how many MB to request the kernel to read
# ahead. If the value is too low the disk may not be fully utilized,
# while if too high the kernel might not be able to keep the read
# pages in memory thus end up trashing.
hash_read_ahead = 8
# Interval between attempts to check the hash, in milliseconds.
#hash_interval = 100
# Number of attempts to check the hash while using the mincore status,
# before forcing. Overworked systems might need lower values to get a
# decent hash checking rate.
hash_max_tries = 5
# Max number of files to keep open simultaniously.
#max_open_files = 128
# Number of sockets to simultaneously keep open.
#max_open_sockets = <no default>
# Example of scheduling commands: Switch between two ip's every 5
# seconds.
#schedule = "ip_tick1,5,10,ip=torretta"
#schedule = "ip_tick2,10,10,ip=lampedusa"
# Remove a scheduled event.
#schedule_remove = "ip_tick1"
# Stop torrents when reaching upload ratio in percent,
# when also reaching total upload in bytes, or when
# reaching final upload ratio in percent.
# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
#schedule = ratio,60,60,"stop_on_ratio=200,200M,2000"
#schedule = ratio,30,60,stop_on_ratio=200
# Enable the default ratio group.
ratio.enable=
# Change the limits, the defaults should be sufficient.
ratio.min.set=200
ratio.max.set=200
ratio.upload.set=20M
# Changing the command triggered when the ratio is reached.
system.method.set = group.seeding.ratio.command, d.close=, d.erase=
# Encryption options, set to none (default) or any combination of the following:
encryption = allow_incoming, try_outgoing, enable_retry
#
# The example value allows incoming encrypted connections, starts unencrypted
# outgoing connections but retries with encryption if they fail, preferring
# plaintext to RC4 encryption after the encrypted handshake
#
# encryption = allow_incoming,enable_retry,prefer_plaintext
# Enable DHT support for trackerless torrents or when all trackers are down.
# May be set to "disable" (completely disable DHT), "off" (do not start DHT),
# "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
# The default is "off". For DHT to work, a session directory must be defined.
#
dht = auto
dht_port = 51778
# UDP port to use for DHT.
#
# dht_port = 6881
# Enable peer exchange (for torrents not marked private)
#
peer_exchange = yes
#
# Do not modify the following parameters unless you know what you're doing.
#
scgi_port = 127.0.0.1:5000
I cannot take credit for these values I found them on another site where they were using the WDTV box and install rtorrent on it. I increase the Max _memory_usage a bit since the WDTV only has 128M memory while I believe the PBO has 256M of memory (not sure on that though). Anyhow those setting works good for me.
Originally Posted by kyle12
:
Reply With Quote
? Create a 
? it never hurts to 
? 
? 